Jackery Explorer 1000 v2 with the EcoFlow 100W Rigid
Works, with caveats · 2S1P · 202 W
Thick mark: cold Voc · Thin mark: operating Vmp, 34.2 V
1 caveat
- The connector type comes from a secondary source, so check the physical port.
Parts for this layout
- Jackery Explorer 1000 v2$559 View on Amazon
- EcoFlow 100W Rigid (2-pack)$239 View on Amazon
- Solar Connector to DC 8mm Adapter Cable, 2M 6.6FT 12AWG+14AWG Solar Cable with DC8020/7909 for Jackery Explorer 160 240 500 1000 GZ Yeti BLUETTI Portable Power Station, Solar Generator, Solar Panel$16.13 View on Amazon
Estimated total $814.13
Prices can change. The price on Amazon at purchase is what applies.
Can I connect the EcoFlow 100W Rigid to the Jackery Explorer 1000 v2?
Yes, with limits. The best setup is 2 panels wired 2S1P on DC 8mm Input 1, delivering up to 202 W. That string reaches 45.3 V at −10 °C against the port’s 60 V limit, using EcoFlow’s published -0.33 %/°C coefficient. Check your own unit’s labels too.
Danger: overvoltage risk. Do not connect the layouts marked red below. Going over a station’s input voltage limit can permanently damage it.
What is the best way to wire EcoFlow 100W Rigid panels to the Jackery Explorer 1000 v2?
Wire them 2S1P on DC 8mm Input 1 for about 202 W from 2 panels. The string runs at 34.2 V, above the 12 V minimum the port needs to start. Stop at 2 in series on the lowest-voltage port, because 3 in series exceeds its limit in the cold.
| Port | Layout | Voc 25 °C | Voc 0 °C | Voc −10 °C | Voc −20 °C | Vmp | Isc | Watts | Verdict at −10 °C |
|---|---|---|---|---|---|---|---|---|---|
| DC 8mm Input 1 | 1S1P | 20.3 | 22.0 | 22.6 | 23.3 | 17.1 | 6.3 | 101 | Works, with caveats |
| DC 8mm Input 1 | 1S2P | 20.3 | 22.0 | 22.6 | 23.3 | 17.1 | 12.6 | 180 | Over the current limit |
| DC 8mm Input 1 | 2S1P | 40.6 | 43.9 | 45.3 | 46.6 | 34.2 | 6.3 | 202 | Works, with caveats |
| DC 8mm Input 1 | 2S2P | 40.6 | 43.9 | 45.3 | 46.6 | 34.2 | 12.6 | 359 | Over the current limit |
| DC 8mm Input 1 | 3S1P | 60.9 | 65.9 | 67.9 | 69.9 | 51.3 | 6.3 | 0 | Danger: overvoltage |
| DC 8mm Input 1 | 4S1P | 81.2 | 87.9 | 90.6 | 93.3 | 68.4 | 6.3 | 0 | Danger: overvoltage |
| DC 8mm Input 2 | 1S1P | 20.3 | 22.0 | 22.6 | 23.3 | 17.1 | 6.3 | 101 | Works, with caveats |
| DC 8mm Input 2 | 1S2P | 20.3 | 22.0 | 22.6 | 23.3 | 17.1 | 12.6 | 180 | Over the current limit |
| DC 8mm Input 2 | 2S1P | 40.6 | 43.9 | 45.3 | 46.6 | 34.2 | 6.3 | 202 | Works, with caveats |
| DC 8mm Input 2 | 2S2P | 40.6 | 43.9 | 45.3 | 46.6 | 34.2 | 12.6 | 359 | Over the current limit |
| DC 8mm Input 2 | 3S1P | 60.9 | 65.9 | 67.9 | 69.9 | 51.3 | 6.3 | 0 | Danger: overvoltage |
| DC 8mm Input 2 | 4S1P | 81.2 | 87.9 | 90.6 | 93.3 | 68.4 | 6.3 | 0 | Danger: overvoltage |
How cold can it get before this string overvolts the Jackery Explorer 1000 v2?
A string of 3 EcoFlow 100W Rigid panels breaches the 60 V limit of DC 8mm Input 1 even at 25 °C, before any cold correction. Voltage rises as cells cool, at EcoFlow’s published -0.33 %/°C, so a clear winter sunrise is the worst case. Stay at 2 in series or fewer there.
The cold-weather correction is the same one NEC Article 690.7 requires for PV system voltage.
Which cable connects the EcoFlow 100W Rigid to the Jackery Explorer 1000 v2?
You need an MC4 to DC8020 adapter cable, rated for at least 6.3 A, to connect this array’s output to DC 8mm Input 1. Confirm the plug against your own station’s port, and check polarity before first use. Keep runs short, because voltage drop grows with current and distance.
How long does the EcoFlow 100W Rigid take to recharge the Jackery Explorer 1000 v2?
Expect about 7.6 peak-sun hours for a full charge from 2 panels. That’s 1.2 days in Denver, CO in June and 1.7 days in December, using a 0.70 real-world derate and NREL irradiance data. Clouds, shade and panel angle can all push it longer.
| City | June | December |
|---|---|---|
| Phoenix, AZ | 1.0 | 1.4 |
| Denver, CO | 1.2 | 1.7 |
| Los Angeles, CA | 1.2 | 1.7 |
| Austin, TX | 1.3 | 1.8 |
| Miami, FL | 1.4 | 1.6 |
| Atlanta, GA | 1.4 | 2.0 |
| Chicago, IL | 1.4 | 2.9 |
| New York, NY | 1.5 | 2.7 |
| Seattle, WA | 1.5 | 4.8 |
Where do these Jackery Explorer 1000 v2 and EcoFlow 100W Rigid numbers come from?
Station limits come from jackery.com and panel ratings from us.ecoflow.com, each checked against a verbatim quote on that page. Panels must also pass a physics test: Vmp times Imp must land within 15% of rated watts. Anything failing goes to quarantine and gets no page.
| Rated power | 100 W | us.ecoflow.com“100 W（+/-5W）” |
|---|---|---|
| Open-circuit voltage (Voc) | 20.3 V | us.ecoflow.com“20.3 V” |
| Operating voltage (Vmp) | 17.1 V | us.ecoflow.com“17.1 V” |
| Short-circuit current (Isc) | 6.3 A | us.ecoflow.com“6.3 A” |
| Operating current (Imp) | 5.9 A | us.ecoflow.com“5.9 A” |
| Voc temperature coefficient | -0.33 %/°C | us.ecoflow.com“-0.33%/°C” |
| Output connector | MC4 | us.ecoflow.comsecondary“Photovoltaic connectors (adapted to MC4 connectors)” |
| DC 8mm Input 1 | 12 to 60 V, 10.5 A, ? W | jackery.com“(2x) DC 8mm Ports: 12-16V(Working Voltage)⎓8A Max,” |
|---|---|---|
| DC 8mm Input 2 | 12 to 60 V, 10.5 A, ? W | jackery.com“(2x) DC 8mm Ports: 12-16V(Working Voltage)⎓8A Max,” |
| DC 8mm Input 1 connector | DC8020 | jackery.com“DC8020 input port” |
| DC 8mm Input 2 connector | DC8020 | jackery.com“DC8020 input port” |
Prices last checked and spec data verified on .