BLUETTI AC180 with the Renogy 100W Flexible
Works, with caveats · 2S1P · 200 W
Thick mark: cold Voc · Thin mark: operating Vmp, 41.4 V
2 caveats
- The maker publishes no temperature coefficient, so cold voltage uses our conservative −0.40 %/°C.
- The connector type comes from a secondary source, so check the physical port.
Parts for this layout
- BLUETTI AC180$498.99 View on Amazon
- 2 × Renogy 100W Flexible$219.98 View on Amazon
- 10 FT Solar to XT60 Extension Cable Solar Panel XT60 Adapter$22.99 View on Amazon
Estimated total $741.96
Prices can change. The price on Amazon at purchase is what applies.
Can I connect the Renogy 100W Flexible to the BLUETTI AC180?
Yes, with limits. The best setup is 2 panels wired 2S1P on Solar Input, delivering up to 200 W. That string reaches 55.6 V at −10 °C against the port’s 60 V limit, using our cautious cold-weather assumption because Renogy publishes no temperature coefficient. Check your own unit’s labels too.
Danger: overvoltage risk. Do not connect the layouts marked red below. Going over a station’s input voltage limit can permanently damage it.
What is the best way to wire Renogy 100W Flexible panels to the BLUETTI AC180?
Wire them 2S1P on Solar Input for about 200 W from 2 panels. The string runs at 41.4 V, above the 12 V minimum the port needs to start. Stop at 2 in series on the lowest-voltage port, because 3 in series exceeds its limit in the cold.
| Port | Layout | Voc 25 °C | Voc 0 °C | Voc −10 °C | Voc −20 °C | Vmp | Isc | Watts | Verdict at −10 °C |
|---|---|---|---|---|---|---|---|---|---|
| Solar Input | 1S1P | 24.4 | 26.8 | 27.8 | 28.8 | 20.7 | 5.2 | 100 | Works, with caveats |
| Solar Input | 1S2P | 24.4 | 26.8 | 27.8 | 28.8 | 20.7 | 10.3 | 200 | Over the current limit |
| Solar Input | 2S1P | 48.8 | 53.7 | 55.6 | 57.6 | 41.4 | 5.2 | 200 | Works, with caveats |
| Solar Input | 2S2P | 48.8 | 53.7 | 55.6 | 57.6 | 41.4 | 10.3 | 401 | Over the current limit |
| Solar Input | 3S1P | 73.2 | 80.5 | 83.4 | 86.4 | 62.1 | 5.2 | 0 | Danger: overvoltage |
| Solar Input | 4S1P | 97.6 | 107.4 | 111.3 | 115.2 | 82.8 | 5.2 | 0 | Danger: overvoltage |
How cold can it get before this string overvolts the BLUETTI AC180?
A string of 3 Renogy 100W Flexible panels breaches the 60 V limit of Solar Input even at 25 °C, before any cold correction. Voltage rises as cells cool, at our assumed −0.40 %/°C (no figure is published), so a clear winter sunrise is the worst case. Stay at 2 in series or fewer there.
The cold-weather correction is the same one NEC Article 690.7 requires for PV system voltage.
Which cable connects the Renogy 100W Flexible to the BLUETTI AC180?
You need an MC4 to XT60 adapter cable, rated for at least 5.2 A, to connect this array’s output to Solar Input. Confirm the plug against your own station’s port, and check polarity before first use. Keep runs short, because voltage drop grows with current and distance.
How long does the Renogy 100W Flexible take to recharge the BLUETTI AC180?
Expect about 8.2 peak-sun hours for a full charge from 2 panels. That’s 1.3 days in Denver, CO in June and 1.8 days in December, using a 0.70 real-world derate and NREL irradiance data. Clouds, shade and panel angle can all push it longer.
| City | June | December |
|---|---|---|
| Phoenix, AZ | 1.1 | 1.5 |
| Denver, CO | 1.3 | 1.8 |
| Los Angeles, CA | 1.2 | 1.8 |
| Austin, TX | 1.4 | 1.9 |
| Miami, FL | 1.5 | 1.7 |
| Atlanta, GA | 1.5 | 2.1 |
| Chicago, IL | 1.5 | 3.1 |
| New York, NY | 1.6 | 2.9 |
| Seattle, WA | 1.7 | 5.2 |
Where do these BLUETTI AC180 and Renogy 100W Flexible numbers come from?
Station limits come from bluettipower.com and panel ratings from renogy.com, each checked against a verbatim quote on that page. Panels must also pass a physics test: Vmp times Imp must land within 15% of rated watts. Anything failing goes to quarantine and gets no page.
| Rated power | 100 W | renogy.com“100 W±3%” |
|---|---|---|
| Open-circuit voltage (Voc) | 24.4 V | renogy.com“24.4 V” |
| Operating voltage (Vmp) | 20.7 V | renogy.com“20.7 V” |
| Short-circuit current (Isc) | 5.16 A | renogy.com“5.16 A” |
| Operating current (Imp) | 4.84 A | renogy.com“4.84 A” |
| Voc temperature coefficient | −0.40 %/°C | Assumed: not published by the maker |
| Output connector | MC4 | renogy.comsecondary“Solar Connectors” |
| Solar Input | 12 to 60 V, 10 A, 500 W | bluettipower.com“500W Max., VOC 12-60VDC, 10A” |
|---|---|---|
| Solar Input connector | XT60 | bluettipower.comsecondary“20A MC4 to XT60 Solar Charging Cable” |
Prices last checked and spec data verified on .